Re: build mellon with -enable-diagnostics to ease up SSO debugging Corey Bryant corey.bryant at Spa is shut down for 15 minutes.Re: build mellon with -enable-diagnostics to ease up SSO debugging Possible inadequate water, poor flow, or air bubbles are detected in the heater.
Ease diagnostics error series#
Master Spa Legend Series (LSX 557) Error Codes If the problem persists, contact your dealer or service organization.
![ease diagnostics error ease diagnostics error](https://imperialcollegehealthpartners.com/wp-content/uploads/2019/08/outcomes-vaules-image-e1565712587962-1024x594.png)
If the display shows only this message (periodically blinking), the spa is shut down. If this is alternating with the temperature, it may just be a temporary condition.
![ease diagnostics error ease diagnostics error](https://www.mdpi.com/diagnostics/diagnostics-12-00746/article_deploy/html/images/diagnostics-12-00746-g003.png)
(May appear temporarily in an overheat situation and disappear when the heater cools.) If the problem p The sensor that is plugged into the Sensor “B” jack is not working. (May appear temporarily in an overheat situation and disappear when the heater cools.) The sensor that is plugged into the Sensor “A” jack is not working. Press any button to leave Standby mode and return to normal operation. Standby Mode has been activated by pressing a button combination on the user panel. Test and reset GFCI per manufacturer’s instructions. Test and adjust sanitizer chemical levels per manufacturer’s instructions. Test and adjust ph chemical levels per manufacturer’s instructions. Remove, clean, and reinstall filter per manufacturer’s instructions.ĭrain and refill spa per manufacturer’s instructions The Priming mode will last for up to 4 minutes and then the spa will begin to heat andĬlean and condition wood per manufacturer’s instructions.
Ease diagnostics error manual#
See the M-7 Installation Instruction Manual for complete instructions on Power-up and Pump Priming. When your spa is first actuated, it will go into Priming mode. If spa does not reset, shut off the power to the spa and call your dealer or service organization. 41.7˚C), the spa should automatically reset. Remove the spa cover and allow water to cool. One of the sensors has detected that the spa water is 110˚F (approximately 43.3˚C).ĭo Not Enter The Water. If spa does not reset, shut off the power to the spa and call your dealer or service organization Once the heater has cooled, reset by pushing any button. 47.8˚C) at the heater.ĭo Not Enter The Water. One of the sensors has detected 118˚F (approx. Heating capacity of the spa will not reset automatically you may press any button to reset. (Displays on the fifth occurrence of the “HFL” message within 24 hours.) Heater is shut down, but other spa functions continue to run normallyįollow action required for “HFL” message. The pumps will automatically activate regardless of spa status. “Ice” - Potential freeze condition detected. Check for dirty filters and clean if necessary If problem persists, contact your dealer or service organization.
![ease diagnostics error ease diagnostics error](https://www.elitechgroup.com/wp-content/uploads/2022/04/EMD-Blood-Borne-Viruses-Banner-490-31MAR2200EN-350x350.png)
If the water level is okay, make sure the pumps have been primed.
![ease diagnostics error ease diagnostics error](https://www.proface.com/library/SCHNEIDER_ELECTRIC/SE_LOCAL/APS/207462_2202/0.2EE.jpg)
This could indicate a flow problem.Ĭheck water level in spa. Spa will not automatically reset you may press any button to resetĪ substantial difference between the temperature sensors was detected. (Displays on third occurrence of “dr” message.) Spa is shut down.įollow action required for “dr” message. If you wish to see the current spa temperature, either switch to Standard mode or turn Jets 1 on for at least two minutes.Īfter the pump has been running for 2 minutes, the temperature will be displayed.Ĭheck water level in spa. In Economy or Sleep mode, the pump may be off for hours outside a filter. Temperature not current in Economy or Sleep mode Spa settings are preserved on all systems. Time of day will be preserved for 30 days on your system. The control panel will be disabled until power returns.